DP28/DPM/DT

Hi,

We are now getting between 1-2 thousand spam mails every day that we sift through to see that we don’t delete legitimate mail. This is a big time killer so until we get the site setup better we are going to ask that if you want to comment or ask a question etc you send it to us at smgguns@yahoo.com .  As of today all bulk spam here will be deleted and the hour or so will shift back to making rifles.  Thanks!

Rick

New Chrome bore DP28 / DPM barrels – as of 12-01-16

Barrels…. We have new made chrome bore barrels sitting on the floor we can sell. They are the exact same barrels we are using in our builds. They are 100% complete minus the gas blocks and gas port hole which we drill to the block on ours and think it is a good plan. The drilling of the gas port and pinning of the gas block can be done by the home builder or we can do it as follows: New barrel ITW, no gas port hole but otherwise 100% – 300.00 + 15.00 shipping. Same barrel with customers gas block pinned on and port hole drilled and assy. hot tank blued – 350.00 + 15.00 shipping.     Money orders and cashier check sales/info to smgguns@yahoo.com   Credit card sales to: smggunsstore.com

As of 01-25-17 we have about 4 of the DPM semi auto rifles within 3 weeks from finished – ready to sell.Pricing:

A complete semi auto DPM from SMG’s kit – purchased from Bowman – and a brand new chrome bore barrel . – 2,750.00 + shipping

     We do have a few DP28 kits to build from but all the shrouds are torched/unusable so we have to make new ones

which ads 175.00 to the cost of a DP28. It will also delay the rifle being built.

A few of the ITEMS BELOW THIS LINE ARE NO LONGER BEING OFFERED – AT LEAST AT THIS TIME. Updated 7-16-16

————————————————————————————————————————–

REALLY ultimate DPM home builders kit

Hi, here we have what we have described as an “ultimate” DPM builders kit. I think it is way past that in that we have taken a DPM kit like you normally purchase and performed ALL the difficult steps required to build a legal semi auto rifle.

First we have welded the receiver back together into a complete unit utilizing one of our new front repair sections. This allows the barrel to be changed out as per the original as well as making all of the required semi auto changes such as blocked forward rails and bolt denial pins. Then we make all the bolt mods and completely assemble it so it is ready to be used. We make all the required cuts and mods to the carrier so it works in the new receiver and with our semi auto bolt. Lastly we completely mill and modify the lower trigger housing to accept all of our semi auto FCG components as well as a working safety made from the original that is repositioned to the left side by your thumb and flips through 90 degrees to operate just like an AR15!

and yes we make sure the barrel shroud will mate up, that a shop barrel goes in properly, that the lower mates to the receiver, etc etc

So you say, what is left for me to do and why are you offering this? Simple. We don’t do all the little fine fit and finish required before bluing. We also don’t head-space the barrel as we do not have the barrel and so you will have to have this done by a qualified gunsmith as part of finishing the build. Past that this is a pretty much plug and play deal. WE DO NOT have barrels and cannot ship you even a de-mil for this package and yes barrels are tough to get but they are out there – how many home builders packages are there like this though? And our price on this kit allows you about 700 under what we charge for a complete DPM rifle to find a barrel and finish it up – and we did the hard work for you!

Ok you ask, so whats different in these parts from what you use to build complete rifles? Nothing – they ARE the same parts. We just felt we would offer some help on the hardest parts of this build and see if anyone is interested.

And yes, since this is a complete receiver it is an FFL item and Texas residents will have to pay sales tax….

No, it does not come with a case – it was just used as a photo backdrop.

Buy 3 or more and get free shipping!

Price for the easiest DPM builders kit ever offered is just $2,000.00 – limited to stock on hand  -  OUT OF STOCK

OUT OF STOCK

Ultimate DP 28 home builders kit

Click on the below pic for a larger image

This is it!

The only easier way is to let us sell you a complete rifle. In this package you receive a complete DP28 parts set, – minus mag – except this one is a bit different.  With this we have done almost all the work for you. You get, in addition to the kit a brand new front receiver section and barrel shroud – forget about having to try to “save” the torched up mess that comes with other kits. You also receive a lower that has been fully modified and tested with all compliant semi auto features and semi auto parts installed – ready to use! As well the bolt and carrier have been completely machined with all semi auto parts installed – also ready to drop right in!

We also don’t head-space the barrel as we do not have the barrel and so you will have to have this done by a qualified gunsmith as part of finishing the build. Past that this is a pretty much plug and play deal. WE DO NOT have barrels and cannot ship you even a de-mil for this package and yes barrels are tough to get but they are out there – how many home builders packages are there like this though?

What is left for you to do? Ok, there has to be something or it wouldn’t be your build right? Ok, you have to weld the two rear halves back together, then saw the front end to length and weld on your welded rear section to our new front section/barrel shroud, weld in the 2 ATF required FA bolt denial pins in the 2 holes you drilled into your rear section, head-space, assemble up all the parts and go test fire!

Ok, the welding is still challenging enough and you have to do your part or it won’t work but these are EXACTLY the same parts – in fact they are THE parts – we use in our builds so if you do your part you will have a cool DP28 that is reliable AND you can do the barrel change as it was designed.  We will also include a short “build help sheet” that might make all the lengths etc you need to shoot for when welding easier.

None of these parts are classified as a firearm so this is NOT an FFL kit – anyone can purchase.

Price for the easiest DP28 builders kit ever offered is just $2,000.00 – limited to stock on hand  -  OUT OF STOCK

OUT OF STOCK

Parts and pieces – odds-n-ends

DPM shown – DP28 receiver does have the “ears” present for the recoil spring retainer on the forward lower edge of the receiver.

 

Complete DP28/DPM receivers: They all say DP28 on the side but it is the same receiver with but a few modifications (that we will do free of charge) to make a DPM. These are fully machined from 4140 bar-stock and include the locking flap recesses, correct barrel shroud threads, and interrupted barrel threads that are properly timed to ensure barrel changing ability. After that the barrel area is EDM machined for the properly timed barrel thread interruptions and then sent out for heat treat to ensure long life. Bolt blocking pins are machined in place.

The price does not include the fitting of your barrel shroud and barrel/barrel latch but is offered separately to ensure a smooth build.This IS a FFL part!

$795.00 – limited to stock on hand.

Receiver front sections

Cutaway section so you can see whats inside.

 

Same description as for the complete receiver but is only the front 3.200″ of the receiver – as measured from where the shroud abuts the receiver. The price also includes the fitting of your barrel shroud and barrel/barrel latch to ensure a smooth build.This IS NOT a FFL part!

$300.00 – limited to stock on hand  -  More being made now – both DP28 and DPM configuration. If interested email us at smgguns@yahoo.com  I am hoping this is the last we make of these.

As of 4-26-12 we have 3 or 4 left to sell.

DP28/DPM and DT  rear Receiver sections


Same description as for the complete receiver but is only the rear of the receiver -  the last 13.5″ as measured from the rear of the receiver – just behind the barrel latch. Includes the completed lock flap recesses.  This has been determined by the ATF to be a FFL part and will carry a serial number with all identifying information and the denial pins will be welded in.

With the exception of getting your overall length and alignment right after/during welding and head-spacing the only fitting in 90% of the cases is in the area of the lower fitment. We could have left this sloppy but we don’t like our builds that way and didn’t figure you did either. A dremel is all that is needed and usually is complete in 15 minutes or less.

The DP28 has a lower screw hole that passes all the way through but these are only through one side as for the DPM/DT series but if you are building a DP 28 we will drill and tap through the other side at no additional charge.

The DT receiver rear has had the swelled flanks on the rear milled flat to accommodate the sliding/collapse-able stock but is otherwise the same as the DPM rear section and could be used for that build allowing the use of a DT sliding stock!

$525.00 – limited to stock on hand

 

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Go to Top